A water heater is supposed to last 10 to 12 years. Around Austin, a lot of them are hauled to the curb at six or seven, and the tank is rarely the problem. What killed it is a few inches of rock sitting on the bottom.
That rock is calcium and magnesium that came out of the water every time the tank heated up. Hard water in water heater tanks builds a layer of scale that insulates the burner from the water, forces the heater to run longer and hotter, corrodes the steel underneath, and eventually opens a seam. When that happens you get 40 to 50 gallons on the floor and a supply line that keeps feeding it until someone shuts the valve.
This guide covers how the buildup forms, what Austin’s water actually measures (the number is lower than most softener ads claim, but not everywhere in the metro), the warning signs, and what to do about it. If your heater has already let go, Titan Water Damage repairs or replaces the unit and dries out the damage with one crew. Call 737-408-7885, any hour.
This post covers:
What Austin Water Really Measures
Search “Austin hard water” and you will find claims of 15, 16, even 18 grains per gallon. Those numbers come from companies selling softeners. Austin Water’s 2025 Consumer Confidence Report puts total hardness at an average of 93 parts per million, or 5.4 grains per gallon, with a range of 70 to 126 ppm across the year. On the USGS scale that is moderately hard.
The reason it is not worse is that Austin Water runs lime softening at its treatment plants. Water pulled from Lake Travis and Lake Austin comes in loaded with dissolved limestone from the Hill Country, and the plants remove a good share of it before it reaches your tap.
Two things to keep in mind, though.
First, moderately hard is still hard enough to scale a water heater. At 5 grains per gallon, a household running 60 gallons of hot water a day pushes several pounds of dissolved mineral through the tank every year, and a portion of it stays behind.
Second, a large part of the Austin metro is not on Austin Water. Round Rock, Cedar Park, Georgetown, Pflugerville, Leander, Buda, Kyle, San Marcos and the Hill Country towns run their own utilities or draw from wells and the Edwards Aquifer. Many of those supplies are noticeably harder than Austin’s, and homes on private wells in Dripping Springs or Wimberley can be harder still. If you live outside the city limits, check your own utility’s annual water quality report rather than assuming Austin’s number applies to you.
How Calcium Build Up in Water Heater Tanks Forms

Calcium carbonate has an odd property. Most things dissolve better in hot water. Calcium carbonate does the opposite. As water temperature rises, its ability to hold dissolved calcium drops, and the mineral falls out of solution as solid scale.
A water heater is the hottest point in the plumbing system, so it is where the most scale forms. Calcium build up in water heater tanks follows a predictable pattern.
- In a gas tank heater, the burner is under the tank floor. Water heats from the bottom, calcium precipitates there, and it settles into a layer of sediment on the tank floor. That layer sits directly between the flame and the water.
- In an electric tank heater, the heating elements are the hottest surfaces, so scale crusts directly onto them. A coated element has to work harder to move heat into the water and eventually burns out.
- In a tankless heater, there is no tank to collect sediment. Instead, scale forms inside the narrow passages of the heat exchanger. Flow drops, the unit throws error codes, and in bad cases it shuts itself down to avoid overheating.
None of this happens overnight. A tank picks up scale a fraction of an inch at a time. The trouble is that nobody sees it until the symptoms start.
Why Water Heater Mineral Buildup Shortens the Life of the Tank
The sediment layer causes four separate problems, and they compound.
It Insulates the Burner from the Water
In a gas heater, the flame now has to heat the sediment before the sediment heats the water. Recovery time gets longer, gas bills go up, and the steel tank floor runs much hotter than it was designed to.
It Overheats the Tank Bottom
That extra heat stresses the steel and the glass lining that protects it. Water trapped in the sediment layer flashes to steam and collapses, which is the popping and rumbling sound people describe. Every one of those pops is a small shock to the tank floor.
It Corrodes the Steel Underneath
Water heater mineral buildup traps a thin layer of water against the tank floor where the sacrificial anode rod cannot protect it. Rust starts under the sediment. The tank looks fine from the outside until a pinhole opens.
It Reduces Capacity and Clogs the Drain
Several inches of sediment displaces several gallons of hot water. The drain valve at the bottom of the tank packs with scale until it will not open, which means the tank can no longer be flushed even if you try.
A heater that would have lasted 12 years in soft water often fails in half that time once the sediment layer gets thick enough. Tankless units are even less forgiving. Most manufacturers void the warranty if the unit is installed on hard water without treatment or a documented descaling schedule.
Warning Signs Your Water Heater Is Scaling Up

- Popping, rumbling or crackling from the tank while it heats. This is the most reliable early sign of sediment.
- Hot water that runs out faster than it used to, with no change in household use.
- Longer recovery time after a shower or a load of laundry.
- Cloudy or gritty hot water, or white flakes in the aerator screens of hot-side faucets.
- A rising gas or electric bill with no other explanation.
- A drain valve that will not open or dribbles when you try to flush.
- Rust-tinted hot water, which means corrosion has started inside the tank.
- Error codes or reduced flow on a tankless unit, especially in winter when incoming water is colder and the unit works harder.
- Any moisture at the base of the tank. A damp spot on the pan or the floor means the tank is already leaking. Shut off the cold supply and the gas or breaker, then call the professionals.
Flushing: How Often, and Why Most Austin Heaters Never Get It
Manufacturers recommend flushing a tank heater once a year. On moderately hard Austin water, once a year is the minimum. On the harder supplies in the suburbs, every six months is closer to right. Most heaters in the metro have never been flushed once.
A flush is not complicated. Turn off the power or set the gas to pilot, shut the cold inlet, connect a hose to the drain valve, open a hot tap somewhere in the house to let air in, and drain the tank. Then open the cold inlet in short bursts to stir up and push out the remaining sediment until the water runs clear.
Two cautions. If the heater is more than eight years old and has never been flushed, draining it can dislodge sediment that was plugging small corrosion holes, and the tank may start leaking afterward. And if the drain valve is packed with scale, forcing it can snap the valve off and empty the tank onto the floor. In either case it is worth having a plumber do the first flush and assess the tank at the same time.
Tankless units need a descaling flush with a pump and a descaling solution circulated through the heat exchanger. Annually is standard. On hard water, more often.
Other Ways to Slow the Buildup
Lower the Thermostat to 120°F
Scale forms faster at higher temperatures. Most tanks ship set higher than that, and 120°F is hot enough for a household while cutting scale formation and scald risk.
Replace the Anode Rod
The anode rod corrodes so the tank does not. It is usually spent after three to five years, and a spent anode leaves the tank floor defenseless under the sediment. Replacing it is inexpensive relative to a new heater.
Consider a Softener or a Scale Inhibitor
Whether it pays off depends on where you live. On Austin Water at 5 grains, it is a judgment call. On a well or a harder municipal supply, a softener or a point-of-use scale inhibitor on the heater’s cold inlet can double the life of the unit.
Install a Pan and a Leak Sensor
A drain pan under the heater with a sensor that alerts your phone turns a flooded closet into a wet pan. If you are on Austin Water, the My ATX Water portal can also alert you to continuous flow, which catches a heater that has started leaking while you are away.
When the Tank Fails: What Happens Next
A tank failure is rarely a trickle. The bottom seam opens, the tank empties, and the cold supply keeps refilling it. Heaters live in closets, garages, attics and utility rooms, so the water goes into drywall, subfloor, insulation and whatever is stored nearby. In an attic install it comes through the ceiling.

Titan Water Damage handles the whole event. Our licensed plumbing team replaces the failed heater, and the same crew runs extraction, structural drying, and mold prevention on everything the tank soaked. One call, one crew, one insurance file. We also carry the moisture readings and photos adjusters need, since most policies cover the sudden water damage but not the heater itself.
Frequently Asked Questions
Is hard water in water heater tanks dangerous?
The scale itself is not a health risk. The risks are a shortened tank life, higher energy bills, and the flood that follows a tank failure. In a gas heater, heavy sediment can also overheat the tank bottom enough to damage the flue baffle, which is worth having inspected if the heater is old and has never been flushed.
How do I know if my water heater has calcium build up?
Listen to it. Popping or rumbling while heating is sediment. Then check the drain valve. If a little water from it comes out cloudy or gritty, the tank has a layer on the bottom. On electric units, a burned-out lower element is a common sign of scale on the element.
Can I remove water heater mineral buildup myself?
For a tank heater under eight years old with a working drain valve, yes. Flush it as described above. For an older tank, a stuck valve, or any tankless unit, have a plumber do it. The risk of turning a maintenance job into a flood is real.
Austin’s water is softer than the ads say, and still hard enough to wreck a water heater that never gets flushed. If yours is popping, running short, or showing damp at the base, call Titan Water Damage. We will assess the tank, replace it if it is done, and dry out anything it damaged, all with one team.

